cat.8100y decoupling device for high frequency higher capacitance. low esr, low esl,high ripple current. resin-molded chip. designed for surface mounting on high density pc board. load life of 5000 hours at + 105 c. compliant to the rohs directive (2002/95/ec). f11 specifications code l tape width (mm) reel dia ( mm) 16 180 k24 330 f & 0 7 m % - 123 5 46 78 91011121314 a h rated capacitance capacitance tolerance case code rated voltage series taping code low esr type numbering system (example : 2.5v 220f) dimensions l 1 l 2 s 2 w 2 p s 1 s 3 w 1 h marking capacitance tolerance f11 0e128m 8j1234 rated capacitance (capacitance code) lot no. rated voltage (voltage code) seriese f case only standard ratings 47 100 220 330 600 800 1200 476 107 227 337 607 807 128 d d ( d ) f d ( d ) f 4 0g 6.3 0j v d d ( d ) f f 2.5 0e code ( ) the series in parentheses are being developed. please contact to your local nichicon sales office when these series are being designed in your application. item performance characteristics category temperature range capacitance tolerance dissipation factor esr leakage current damp heat (steady state) temperature cycles temperature change characteristics resistance to soldering heat surge endurance marking ? 55 to +105 c 20% (at 120hz) refer to next table refer to next table after 5 minute s application of rated voltage, leakage current is not more than 0.1cv ? 55 c / +105 c 30minutes each 5cycle ? 55 c +105 c at 60 c 90%rh 500hours (no voltage applied) capacitance change .. within ? 20 to +30% of the initial specified value dissipation factor ....... 200% or less than the initial specified value esr ............................ 200% or less than the initial specified value leakage current ......... initial specified value or less capacitor meets the following characteristics after solder reflow (peak: 240 c for 10sec, 2cycle). temperature should be measured at the terminals. capacitance change .. within 20% of the initial specified value dissipation factor ....... 200% or less than the initial specified value esr ............................ 200% or less than the initial specified value leakage current ......... initial specified value or less capacitance change .. within 20% of the initial specified value dissipation factor ....... initial specified value or less esr ............................ initial specified value or less leakage current ......... initial specified value or less capacitance change dissipation factor esr leakage current within ? 20 to +0% initial specified value or less initial specified value or less initial specified value or less within ? 0 to +50% 150% or less than the initial specified value 150% or less than the initial specified value 10 times initial specified value after application of 115% of rating voltage at the rate of 30 seconds on, 30 seconds off, for 1000 successive test cycles at 105 c, capacitors meet the characteristics requirements listed below. capacitance change .... within 20% of the initial specified value dissipation factor ......... 200% or less than the initial specified value esr .............................. 200% or less than the initial specified value leakage current ........... initial specified value or less after 5000 hours application of rated voltage at 105 c, they will meet the specified value for life charecteristics listed below. capacitance change .... within 20% of the initial value dissipation factor ......... 200% or less than the initial specified value esr .............................. 200% or less than the initial specified value leakage current ........... initial specified value or less printed on the package top. ( mm ) case code d f l 1 l 2 w 1 w 2 h 8.5 0.2 16.7 0.2 7.3 0.2 15.6 0.2 5.3 0.2 12.1 0.2 1.7 0.2 3.6 0.2 2.0max. 2.5max. s 1 0.9 0.2 1.5 0.1 s 2 0.6 0.2 1.3 0.1 s 3 0.5 0.2 1.5 0.2 p 3.3 0.2 7.0 0.2 cap.( f )
f11 ratings table layout land pattern (example) frequency characteristic < standard > < low esr > case abb cc 5.5 1.4 1.2 0.5 1.9 d 1.8 1.2 6.6 1.8 14 f case abb c 5.5 1.0 4.3 0.6 d 10.2 1.2 1.8 14 f 100 10 1 0.1 100k 1m 10m 100m 1g 10g inpedance (mohm) frequency (hz) the characteristics are measured by a network analyzer and converted from s21 to impedance. 2.5v -220 f(d) 2.5v -1200 f(d) < notice > the graph illustrates representative data. please use this for reference only. 12.0 0 1.5 15.0 15.0 0 4.5 11.5 0 4.0 0 4.0 0 5 10 0 5 0 5 0 220 1200 0 100 00 47 0 55 300 0 40 0 30 2.5 4 .0 6.3 f110e227mdlah1 f110e128mfkah3 f110g107mdlah1 f110j476mdlah1 d f d d rated ripple (arms@300khz) part number leakage current ( a) disspation factor (% @120hz) case code esr (m ? @300khz) rated volt (v) rated capacitance (f) (mm) (mm) decoupling device for high frequency 2.5v - 1200f (f) 2.5v - 220f (d) 6.3v - 47f (d) 4v - 100f (d) 20.0 20.0 0 5.0 0 5.0 20.0 20.0 0 5.0 20.0 0 5.0 3.5 3.5 6.3 6.3 3.5 3.5 6.3 3.5 6.3 0 5 0 5 10 10 0 5 0 5 10 0 5 10 0 100 0 220 0 600 1200 00 47 0 100 0 800 00 47 0 600 0 25 0 55 150 300 0 19 0 40 320 0 30 378 2.5 4 .0 6.3 f110e107mdl f110e227mdl f110e607mfk f110e128mfk f110g476mdl f110g107mdl f110g807mfk f110j476mdl f110j607mfk d d d d f f f f d d d d f f d d f f rated ripple (arms@100khz) part number leakage current ( a) disspation factor (% @120hz) case code esr (m ? @100khz) rated volt (v) rated capacitance (f) cat.8100y
|
